Photo Mask

PAM-XIAMEN Offers Photomasks

A photo mask is a thin coating of masking material supported by a thicker substrate, and the masking material absorbs light to varying degrees and can be patterned with a custom design. The pattern is used to modulate light and transfer the pattern through the process of photolithography which is the fundamental process used to build almost all of today’s digital devices.

  • Description

Product Description

Photo Mask

PAM-XIAMEN Offers Photomasks

Photomask Large Size

Photomask Middium and Small Size

Photographic plate

Photographic Film Letterpress

Photographic Film

Chrome Photomask

Chromium Photomask Blank

Photolithography Mask

photo mask is a thin coating of masking material supported by a thicker substrate, and the masking material absorbs light to varying degrees and can be patterned with a custom design. The pattern is used to modulate light and transfer the pattern through the process of photolithography which is the fundamental process used to build almost all of today’s digital devices.

What is a Photomask

A photomask is an opaque plate with holes or transparencies that allow light to shine through in a defined pattern. They are commonly used in photolithography. Lithographic photomasks are typically transparent fused silica blanks covered with a pattern defined with a chrome metal-absorbing film. Photomasks are used at wavelengths of 365 nm, 248 nm, and 193 nm. Photomasks have also been developed for other forms of radiation such as 157 nm, 13.5 nm (EUV), X-ray, electrons, and ions; but these require entirely new materials for the substrate and the pattern film. A set of photomask, each defining a pattern layer in integrated circuit fabrication, is fed into a photolithography stepper or scanner, and individually selected for exposure. In double patterning techniques, a photomask would correspond to a subset of the layer pattern. In photolithography for the mass production of integrated circuit devices, the more correct term is usually photoreticle or simply reticle. In the case of a photomask, there is a one-to-one correspondence between the mask pattern and the wafer pattern. This was the standard for the 1:1 mask aligners that were succeeded by steppers and scanners with reduction optics. As used in steppers and scanners, the reticle commonly contains only one layer of the chip. (However, some photolithography fabrications utilize reticles with more than one layer patterned onto the same mask). The pattern is projected and shrunk by four or five times onto the wafer surface. To achieve complete wafer coverage, the wafer is repeatedly “stepped” from position to position under the optical column until full exposure is achieved. Features 150 nm or below in size generally require phase-shifting to enhance the image quality to acceptable values. This can be achieved in many ways. The two most common methods are to use an attenuated phase-shifting background film on the mask to increase the contrast of small intensity peaks, or to etch the exposed quartz so that the edge between the etched and unetched areas can be used to image nearly zero intensity. In the second case, unwanted edges would need to be trimmed out with another exposure. The former method is attenuated phase-shifting, and is often considered a weak enhancement, requiring special illumination for the most enhancement, while the latter method is known as alternating-aperture phase-shifting, and is the most popular strong enhancement technique. As leading-edge semiconductor features shrink, photomask features that are 4× larger must inevitably shrink as well. This could pose challenges since the absorber film will need to become thinner, and hence less opaque. A recent study by IMEC has found that thinner absorbers degrade image contrast and therefore contribute to line-edge roughness, using state-of-the-art photolithography tools. One possibility is to eliminate absorbers altogether and use “chromeless” masks, relying solely on phase-shifting for imaging. The emergence of immersion lithography has a strong impact on photomask requirements. The commonly used attenuated phase-shifting mask is more sensitive to the higher incidence angles applied in “hyper-NA” lithography, due to the longer optical path through the patterned film.

Mask Materials -Difference between Quartz and Soda Lime Glass:

The most common types of glass for manufacturing masks are Quartz and Soda Lime. Quartz is more expensive, but has the advantage of a much lower coefficient of Thermal Expansion (which means it expands less if the mask gets warm during use) and is also transparent at deeper Ultraviolet (DUV) wavelengths, where Soda Lime glass is opaque. Quartz needs to be used where the wavelength being used to expose the mask is less than or equal to 365nm (i-line).A photolithography mask is an opaque plate or film with transparent areas that allow light to shine through in a defined pattern. They are commonly used in photolithography processes, but are also used in many other applications by a wide range of industries and technologies. It exists different kind of mask for different application namely based on the resolution needed.

For more product detail, please contact us at luna@powerwaywafer.com or powerwaymaterial@gmail.com.

 

1X Master Mask

1X Master Mask Dimensions and Substrate Materials

Product Dimensions Substrate Materials
1X Master 4” X4” X0.060” or 0.090” Quartz and Soda Lime
5” X5” X0.090” Quartz and Soda Lime
6” X6” X0.120” or 0.250” Quartz and Soda Lime
7” X7” X0.120” or 0.150” Quartz and Soda Lime
7.25” Round X 0.150” Quartz
9”X9”X0.120” or 0.190” Quartz and Soda Lime

 

Common Specifications for 1X Master Masks(Quartz Material)

CD Size CD Mean-to-Nominal CD Uniformity Registration defect Size
2.0 um ≤0.25 um ≤0.25 um ≤0.25 um ≥2.0 um
4.0 um ≤0.30 um ≤0.30 um ≤0.30 um ≥3.5 um

 

Common Specification for 1X Master Masks(Soda Lime Material)

CD Size CD Mean-to-Nominal CD Uniformity Registration defect Size
≤4 um ≤0.25 um ———— ≤0.25 um ≥3.0 um
>4 um ≤0.30 um ———— ≤0.45 um ≥5.0 um

 

UT1X Mask

UT1X Mask Dimensions and Substrate Materials

Product Dimensions Substrate Material
UT1X 3″ X5″ X0.090″ Quartz
5″ X5″ X0.090″ Quartz
6″ X6″X0.120″ or 0.250″ Quartz

 

Common Specifications for UT1X Masks

CD Size CD Mean-to-Nominal CD Uniformity Registration defect Size
1.5 um ≤0.15 um ≤0.15 um ≤0.15 um ≥0.50 um
3.0 um ≤0.20 um ≤0.20 um ≤0.20 um ≥0.60 um
4.0 um ≤0.25 um ≤0.25 um ≤0.20 um ≥0.75 um

 

Standard Binary Masks

Standard Binary Mask Dimensions and Substrate Materials

Product Dimensions Substrate Materials
2X 6″X 6″ X0.250″ Quartz
2.5X
4X
5X 5″ X5″ X0.090″ Quartz
6″ X6″ X0.250″ Quartz

 

Common Specifications for Standard Binary Masks

CD Size CD Mean-to-Nominal CD Uniformity Registration defect Size
2.0 um ≤0.10 um ≤0.15 um ≤0.10 um ≥0.50 um
3.0 um ≤0.15 um ≤0.15 um ≤0.15 um ≥0.75 um
4.0 um ≤0.20 um ≤0.20 um ≤0.20 um ≥1.00 um

 

Medium Area Masks

Medium Area Mask Dimensions and Materials

Product Dimensions Substrate Materials
1X 9″ X9″ 0.120″ Quartz Soda Lime(both Chrome and Iron Oxide absorbers available)
9″ X9″ 0.190″ Quartz

 

Common Specifications for Medium Area Masks(Quartz Material)

CD Size CD Mean-to-Nominal CD Uniformity Registration defect Size
0.50 um ≤0.20 um ———— ≤0.15 um ≥1.50 um

 

Common Specifications for Medium Area Masks(Soda Lime Material)

CD Size CD Mean-to-Nominal CD Uniformity Registration defect Size
10 um ≤4.0 um ———— ≤4.0 um ≥10 um
4 um ≤2.0 um ———— ≤1.0 um ≥5 um
2.5 um ≤0.5 um ———— ≤0.75 um ≥3 um

You may also like…